• Out-of-Stock
Atlas BP8000 2 Post Bottom Plate Car Lift (8,000lbs Capacity)
search
  • Atlas BP8000 2 Post Bottom Plate Car Lift (8,000lbs Capacity)

Atlas BP8000 2 Post Bottom Plate Car Lift (8,000lbs Capacity)

$3,995.00

Atlas BP8000 2 Post Bottom Plate Car Lift (8,000lbs Capacity)

Quantity
Out-of-Stock

  Security policy

(edit with the Customer Reassurance module)

  Delivery policy

(edit with the Customer Reassurance module)

  Return policy

(edit with the Customer Reassurance module)

The Atlas BP8000 is a base-plate two-post lift designed for low ceiling garages. The total column height of 108" (9 feet) allows this lift to be installed in almost any professional or home garage with a ceiling as low as 9 feet 3 inches.

Benefits Of Our Atlas BP8000 2-Post 8000lb Capacity Carlift

The Atlas BP8000 incorporates an innovative standard manual single-point safety release, automatic arm restraints, powder coat finish, and heavy-duty chain mounted over dual reliable hydraulic cylinders (one cylinder in each column).

Chain-Over-Roller Cylinder Configuration: The Atlas BP8000 has the chain-over-roller cylinder configuration. The lift is designed to utilizes the two most popular hydraulic cylinder configurations used in two post electric/hydraulic above ground lifts; the direct drive cylinder configuration and the chain-over-roller cylinder configuration. The base plate two post above ground lift implements the chain-over-roller configuration. This is the only hydraulic cylinder system that is possible in the base plate lift.

The base plate two post above ground is designed for "low ceilings". The direct drive hydraulic cylinder configuration cannot be used in the base plate lift because the hydraulic cylinder would extend above the 9' column when the lift arms were raised to the maximum height. The "overhead" two post above ground lift may incorporate either the direct drive hydraulic cylinder or the chain-over-roller hydraulic cylinder. Super

Single-Point Technology: The Atlas BP8000 features a revolutionary designed manual single-point safety release system for the BP8000 8,000lb. base-plate lift. The super single-point manual release allows the operator to unlock both column locks from the power unit column. Many manufacturers incorporate 24 volt electro-mechanical lock release systems that are complicated and unreliable. A manual single-point lock release system provides a mechanically proven system that will perform flawlessly for many years.

Double Lock System: The Atlas BP8000 introduces a revolutionary double lock system installed in both lift columns. This new lock system incorporates two locking mechanisms for added safety. The double lock system is automatically activated as the lift is raised. When the vehicle reaches the desired height, the lift is lowered into the next lowest locking position. When the vehicle is ready to be lowered to the ground, the double lock system is disengaged by pulling a handle located near the power unit. There is no need for the operator to go to both columns and manually unlock both column locks. All lifting and lowering operations are controlled from one column post. Double safety locks built into each column that can be unlocked by one release lever make the Atlas BP8000 base plate lift the safest and easiest to operate base plate lift in the Industry. Two locks...one release...no hassle...available only from ATLAS!

Electrical Requirement: The electric motor for the power unit requires 220 Volt (single phase) 60 Hz. We recommend using at least a 10 gauge (grounded) wire from the electrical panel. The power unit has a short pigtail (no plug) that can be wired to either a quick disconnect box (mounted on the lift column) or to a male/female plug combination. A 30 amp breaker is recommended.

Highlights

  • 8,000 lb. Capacity
  • Single Point Lock Release
  • Base Plate Design
  • Dual Hydraulic Chain-Drive Cylinders
  • Double Lock System
  • Automatic Arm Restraints
  • 2 Stage Symmetric Arm Design
  • Self-Lubricating HMW Polyethylene Sliders and Bronze Bushings
  • Powder Coat Finish
  • FREE 12 Piece Truck Adaptor Set
  • Mounting Hardware Included
  • Shipping Weight: 1,290 lbs.
Specifications
Capacity 8,000 LB.
Lifting Time Ask Your Salesperson
Overall Height 108" (9')
Overall Width 132" (11')
Outside Column to Outside Column 124" (10' 4")
Maximum Lift Height (Without Adapters) 70 1/2" (5' 10 1/2")
Maximum Lift Height (With Adapters) 81 1/8" (6' 9 1/8")
Minimum Arm Height 3 1/2"
Base Plate Width 11 1/2"
Inside Column 109 5/8" (9' 1 5/8")
Drive Thru 99" (8' 3")
Column Size 7 1/4" x 11"
Column Thickness of Steel 6mm
Arms Thickness of Steel 6mm
Cable Diameter .375"
Carriage Thickness of Steel 6mm
Base Of Lift (17 1/2" x 17 3/4")
Motor/Electrical Requirement 3 HP 220V +/- 5% (209-231volts) single (1) phase.
A 30 amp breaker is required.
Oil Requirement 3-5 Gallons AW32/AW46
Shipping Weight 1,290 LB.
BP8000